6414 tubes

For the serious and not so serious in audio: DoItYourself and Tubes (SET, PP, Vintage).

Moderator: kabubi

6414 tubes

Postby iceman90a » Fri Dec 21, 2007 4:28 pm

my amp uses a pair of 6414 tubes, do these get consumed quickly? where can i buy a pair for backup? any brand recommendations?

thanks
User avatar
iceman90a
Fanatic
Fanatic
 
Posts: 1530
Joined: Mon Jun 30, 2003 4:06 pm

Re: 6414 tubes

Postby iceman90a » Sat Jun 29, 2013 9:41 am

still looking...
User avatar
iceman90a
Fanatic
Fanatic
 
Posts: 1530
Joined: Mon Jun 30, 2003 4:06 pm

Re: 6414 tubes

Postby Gau_Ban » Sat Jun 29, 2013 11:55 am

6414:

An industrial, computer rated dual triode,virtually the same specs as the E180CC or 7062 listed above. Unlike the E180CC, this tube was made in the USA. It is a more rugged build, with the Raytheon blackplate type sporting triple mica and military ratings. This tube is also like a 12AV7 and will work wonders in any 12AT7 spot, and may be just the ticket if you want to boost the gain of a 12AU7 circuit. The 6414 is getting very hard to find, but with a 10,000 hour heater rating you may never need a replacement. Discussion groups rate this type very highly for use in headphone amps. Stands about 1/2 inch taller than the standard 12AT7.

From here
http://www.audiotubes.com/12at7.htm

Because this tube was rated for computer use, expect a long life. Since it was made only in the USA, they were made by Raytheon and GE. Supposedly a lot of the available tock was snatched up by Manley.
Gau_Ban
Citizen
Citizen
 
Posts: 807
Joined: Fri Jan 24, 2003 1:33 pm

Re: 6414 tubes

Postby tony » Fri Oct 04, 2013 7:39 pm

iceman90a wrote:still looking...



peanut tubes outlasts the power tubes longer..

JJ 12AT7 can be purchased here....http://www.epektos.com/product/cb3db681 ... bc2c7.aspx

you may want to try 6201 from Gerry Sta Maria....5237551
User avatar
tony
Fanatic
Fanatic
 
Posts: 1882
Joined: Tue Jun 24, 2003 7:18 am
Location: Pasig City....

Re: 6414 tubes

Postby kabubi » Fri Oct 04, 2013 10:17 pm

Gau_Ban wrote:6414:

An industrial, computer rated dual triode,virtually the same specs as the E180CC or 7062 listed above. Unlike the E180CC, this tube was made in the USA. It is a more rugged build, with the Raytheon blackplate type sporting triple mica and military ratings. This tube is also like a 12AV7 and will work wonders in any 12AT7 spot, and may be just the ticket if you want to boost the gain of a 12AU7 circuit. The 6414 is getting very hard to find, but with a 10,000 hour heater rating you may never need a replacement. Discussion groups rate this type very highly for use in headphone amps. Stands about 1/2 inch taller than the standard 12AT7.

From here
http://www.audiotubes.com/12at7.htm

Because this tube was rated for computer use, expect a long life. Since it was made only in the USA, they were made by Raytheon and GE. Supposedly a lot of the available tock was snatched up by Manley.


can it be used as a preamp tube? or a phono stage tube?
User avatar
kabubi
Legend
Legend
 
Posts: 5476
Joined: Wed Oct 26, 2005 6:28 pm

Re: 6414 tubes

Postby tony » Sat Oct 05, 2013 7:19 am

the 12AV7 has lower mu than the 12AT7, but i doubt that
will matter in a typical common cathode circuit....
the good news is that it has higher transconductance and
lower plate resistance, so that output impedance in a circuit
is lower and output swing can be higher,
a higher output swing means more undistorted output....
User avatar
tony
Fanatic
Fanatic
 
Posts: 1882
Joined: Tue Jun 24, 2003 7:18 am
Location: Pasig City....


Return to DIY and Tubes

Who is online

Users browsing this forum: No registered users and 2 guests