SPARE PARTS Wish LIst

[hypertriode]

If it's not asking too much, Mickey:
1. more RIKEN resistor values.
2. cheaper audio-grade filter capacitors (aside from black gate and cerafine).
3. hovland musicaps.
4. ELMA or DACT selector switches.
5. PCB-mount ceramic, gold-plated 9-pin sockets.
6. 400 volts MULTICAP RTX caps.
7. TANTALUM resistors.

[isak0411]

100uf/16v fk backgate
100vf/160v fk backgate
4700uf/16v backgate
0,1vf/400v rtx/auricap
100uf x2/500v cerafine

[mickey]

Guys,

Its embarrassing that you arrived at this site before I did. Anyway will start posting our stuff according to their category. I'll update these list as new stuff arrives. Hope you will be patient with me specially with the stuff that are not on the list. Thanks. Isak, emailed u your wish.

Mickey

[mozilla]

Mickey,

Will you have these Alps Stepped Pots soon?

[mickey]

Grant,

Sorry havent seen anything like that before. But checking. gimme a few days to tell u if Alps made that. if they did. then I can get those for you.

Rene,

PCB mount 9 pins should be here in 2.5 weeks time. Check out The F&T filter Caps.

Mickey

[zach]

ey there, meron kang mga female iec connectors?

[mickey]

yup. have Bulgin fused IEC connectors

[hahnsoloist]

sir ako EL84 na sovtek or tesla, pricelist po. ty

[vintage_dog]

Mickey,

Will you have these Alps Stepped Pots soon?

these are the FAKE ALPS.

[mickey]

Yup they sure are!

[Quiel]

more auricaps like .33 and .068 at 250V or higher...

[mickey]

have .33 600V coming in. Where you using this?

[Quiel]

for input tube duties, haven't checked the wirings really so can't tell specific function. but this is to experiment w/ my PP amp... long overdue project. currently, these are film caps type.

[brady]

Hi Mickey. Suggestion : large diameter colored shrinkables for DIY AC cord terminals - at the gear end and at the Meralco end. Or DIY RCA ICs. Maski 3-4 inches length lang. Sa RS one has to buy large volumes.

[mickey]

Hi Quiel, Maybe you can check out your circuit, the input cap could be used to isolate the grid from the input. I had one of these when I used fixed bias on the first stage. DC blocker Arnold would call it. You can used a diff value here. just compute the cutoff freq. = 1/(2*3.24*R*C ) - R being the grid to ground resistor.So with a smaller cap you can use a bigger resistor or the other way around using a smaller cap with a bigger resistor and you get the same cutoff freq.

Hi Brady, Will check those out. If you need DIY ICs I have some bullet plugs. can give you #34 magnet wires. they sound great! nice highs. the theory i learned here is that the thinner the wire the lower the resistance to high freq. so i just put several strands in a teflon tube to improve the bass. tough part here is the scraping of the varnish. cant burn it off. its too thin.

[s2kov]

How about any metallized polyprop caps with the following values:

1. 22uF/500V
2. 47uF/500V
3. 100uF/500V

[mickey]

Sorry s2kov don't have those in the pipeline.

[s2kov]

Non-Polar blackgate caps (47uF/63V)
Auricap 0.47/450V

[bruno]

I saw some Blackgate N on Silver Strings the last time I went there but they don't have prices yet. Values were 10uF/50v, 100uF/16v and 1000uF/50v. Any prices yet for these Sir Mickey?

[mickey]

Will update our list tom. Thanks

S2kov, we have the .47 uf 450V on stock.